Shop – Check Reality 3D Printed Products

Red Sea Reefer Adjustable Return Flow With Random Flow Nozzles

Nat — Thu, 08 Aug 2019 19:44:14 +0000

This is a custom part designed by myself, being a reef keeper and Red Sea Reefer tank owner, I produced this to solve the issues of the standard return nozzle. My 3D printed adjustable dual return pipe for the Red Sea Reefer Series of tanks allows you to split the return flow from the standard stock pipe

The addition of two injection moulded fully adjustable pipes in conjunction with random flow nozzles on each end provides random flow within the tank.

Each arm of the return pipe allows you to direct the return flow where it is needed for better health of the ecosystem. Key benefits of this modification are running higher flow rates through this dual nozzle replacement and also stopping your sand bed from being blown around in the tank.

The Red Sea Reefer dual return pipe is suitable for all tanks in the Reefer range, including the Red Sea Reefer Nano / 170 / 250 / 350 / 450 / XL 425 / XL 525 / XXL 625 / XXL 750 / Peninsula 500 / Peninsula 650.

Installation is simple just remove the stock Red Sea Reefer inner return pipe, this just pulls out, then just slide this into the stock return pipe.

The 3D printed return nozzle is the strongest available, printed using PLA+ this is several times tougher than PLA and PETG. Then each part is annealed, annealing plastic involves gently reheating the substance to a point above its glass transition temperature, but below its melting temperature, and then slowly allowing it to cool. Like the annealing of metal, this reheating and cooling increases the amount of crystalline structures in the plastic. Both of these things, in turn, makes the plastic stronger, stiffer and more resistant to the stresses that cause failure.

Highlights:

Red Sea Reefer Dual Return Pipe Nozzle

Nat — Tue, 22 May 2018 12:49:48 +0000

First of all being a reef keeper and Red Sea Reefer tank owner I experienced in tank problems with the standard return pipe. I produced this custom Red Sea Reefer dual return pipe to solve issues with the stock return pipe. My 3D printed dual return pipe nozzle for the Red Sea Reefer Series of tanks allows you to split the return flow from the standard stock pipe providing more random flow within the tank for better health of the ecosystem. Key benefits are running higher flow rates through this split pipe replacement part and stopping your sand bed from being blown around in the tank.

Hence installation is simple just remove the stock Red Sea Reefer inner return pipe, this just pulls out. Then just slide this into the stock return pipe.

As a result my 3D printed return nozzle is the strongest available and totally reef safe. Due to printing using PLA+ each part is several times tougher than PLA or PETG. First of all each part is annealed, annealing plastic involves gently reheating the substance to a point above its glass transition temperature, but below its melting temperature, and then slowly allowing it to cool. So like the annealing of metal, this reheating and cooling increases the amount of crystalline structures in the plastic. Both of these things in turn, makes the plastic stronger stiffer and resistant to the stresses that cause failure.

Highlights:

Low Profile 120mm Fan to 4 Inch / 100mm Pipe Ducting

Nat — Wed, 14 Feb 2018 21:58:16 +0000

Another original design developed to meet a customers exacting specification for an ultra low profile cooling fan duct. This design enables quick fitment to a standard 120mm fan using original screws allowing you to reduce heat and noise. Production of our low profile cooling fan duct ventilation adapter is only available in black PETG.

Fan shroud adapters allow you to exhaust heat from a room using standard 4 inch ventilation ducting. It is easy to fit fan shroud adapters to any standard 120mm cooling fan. Each fan shroud vent adapter has a lip on the hose connection side. Ease of installation is achieved with secure fitment of the ventilation ducting pipe being tie wrapped into place ensuring it will not slip off the shroud.

Each 3D printed low profile cooling fan duct is the strongest available, printed using PETG being several times tougher than PLA and PLA+. Parts are annealed, annealing plastic involves controlled reheating the plastic to a point above it’s glass transition temperature, but below melting temperature, and then allowing it to cool. Like the annealing of metal, this reheating and cooling increases the amount of crystalline structures in the plastic. Both of these things, in turn, makes the plastic stronger, stiffer and more resistant to the stresses that cause failure.

Highlights:

120mm Fan Adapter to 6 Inch / 152mm Vent Duct Pipe

Nat — Thu, 01 Feb 2018 20:30:34 +0000

If you need maximum airflow, our largest diameter duct adapter keeps temperatures as low as possible, improving hardware efficiency and increasing longevity. Designed to fit the standard 120mm fans using your original screws this will allow you to reduce heat and noise in the room your hardware is located. The large cooling fan duct pipe adapter allows you to easily exhaust heat out of the room using standard 6 inch (152mm) ducting. The shroud adapter can be used with any standard 120mm fan. This vent adapter has a lip on hose connection side, allowing for a safe and secure fitting of the vent ducting hose which can then be tie wrapped in place and will not slip or slide off the shroud.

The large six inch cooling fan duct shrouds are the strongest available, printed using PETG this is several times tougher and more heat resistant than PLA and PLA+. Each part is annealed, annealing plastic involves gently reheating the substance to a point above its glass transition temperature, but below its melting temperature, and then slowly allowing it to cool. Like the annealing of metal, this reheating and cooling increases the amount of crystalline structures in the plastic. Both of these things, in turn, makes the plastic stronger, stiffer and more resistant to the stresses that cause failure.

Highlights:

Bitmain Antminer S9 T9 V9 D3 A3 E3 X3 L3 Z9 Fan Duct Cooling Shroud to 5 Inch / 125mm Vent

Nat — Wed, 10 Jan 2018 01:12:39 +0000

Ideal for keeping temperatures low and increasing mining efficiency, designed to fit the standard 120mm fans using your original screws this will allow you to reduce heat and noise in the room your miners are located. The shroud pipe adapter allows your Antminer to easily exhaust heat out of the room using standard 5 inch (125mm) ducting. A cool miners equals better hash rates. The shroud adapter can be used with any standard 120mm fan. This vent adapter has a lip on hose connection side, allowing for a safe and secure fitting of the vent ducting hose which can then be tie wrapped in place and will not slip or slide off the shroud.

My 3D printed vent shrouds are the strongest available, printed using PETG this is several times tougher than PLA and PLA+. Then each part is annealed, annealing plastic involves gently reheating the substance to a point above its glass transition temperature, but below its melting temperature, and then slowly allowing it to cool. Like the annealing of metal, this reheating and cooling increases the amount of crystalline structures in the plastic. Both of these things, in turn, makes the plastic stronger, stiffer and more resistant to the stresses that cause failure.

Highlights:

Bitmain Antminer S9 D3 A3 V9 E3 X3 L3 Z9 120mm Fan Duct Cooling Shroud 4 Inch / 100mm Vent

Nat — Sat, 06 Jan 2018 00:17:47 +0000

Perfect for keeping temperatures low, improving mining efficiency and increasing longevity of your miner. Designed to fit the standard 120mm fans using your original screws this will allow you to reduce heat and noise in the room your miners are located. The shroud pipe adapter allows your Antminer to easily exhaust heat out of the room using standard 4 inch (100mm) ducting. A cool miners equals better hash rates. The shroud adapter can be used with any standard 120mm fan. This vent adapter has a lip on hose connection side, allowing for a safe and secure fitting of the vent ducting hose which can then be tie wrapped in place and will not slip or slide off the shroud.

Highlights:

Black Cable Ties Pack Of 10

Nat — Mon, 01 Jan 2018 18:52:37 +0000

Perfect for securing duct pipe to our mining adapters, these are also suitable for securing or retaining cable / pipe bundles and objects of various shapes and sizes. The design of the head guarantees a high tensile strength while allowing a very low insertion force.